# # GENERIC -- Generic machine with WD/AHx/NCR/BTx family disks # # For more information read the handbook part System Administration -> # Configuring the FreeBSD Kernel -> The Configuration File. # The handbook is available in /usr/share/doc/handbook or online as # latest version from the FreeBSD World Wide Web server # # # An exhaustive list of options and more detailed explanations of the # device lines is present in the ./LINT configuration file. If you are # in doubt as to the purpose or necessity of a line, check first in LINT. # # $Id: GENERIC,v 1.143.2.2 1999/02/15 02:50:07 des Exp $ machine "i386" cpu "I386_CPU" cpu "I486_CPU" cpu "I586_CPU" cpu "I686_CPU" ident PCCARD maxusers 10 options MATH_EMULATE #Support for x87 emulation options INET #InterNETworking options FFS #Berkeley Fast Filesystem options FFS_ROOT #FFS usable as root device [keep this!] options MFS #Memory Filesystem options MFS_ROOT #MFS usable as root device, "MFS" req'ed options NFS #Network Filesystem options NFS_ROOT #NFS usable as root device, "NFS" req'ed options MSDOSFS #MSDOS Filesystem options "CD9660" #ISO 9660 Filesystem options "CD9660_ROOT" #CD-ROM usable as root. "CD9660" req'ed options PROCFS #Process filesystem options "COMPAT_43" #Compatible with BSD 4.3 [KEEP THIS!] options SCSI_DELAY=15000 #Be pessimistic about Joe SCSI device options UCONSOLE #Allow users to grab the console options FAILSAFE #Be conservative options USERCONFIG #boot -c editor options VISUAL_USERCONFIG #visual boot -c editor config kernel root on wd0 # To make an SMP kernel, the next two are needed #options SMP # Symmetric MultiProcessor Kernel #options APIC_IO # Symmetric (APIC) I/O # Optionally these may need tweaked, (defaults shown): #options NCPU=2 # number of CPUs #options NBUS=4 # number of busses #options NAPIC=1 # number of IO APICs #options NINTR=24 # number of INTs controller isa0 controller eisa0 controller pci0 controller fdc0 at isa? port "IO_FD1" bio irq 6 drq 2 disk fd0 at fdc0 drive 0 disk fd1 at fdc0 drive 1 options "CMD640" # work around CMD640 chip deficiency controller wdc0 at isa? port "IO_WD1" bio irq 14 disk wd0 at wdc0 drive 0 disk wd1 at wdc0 drive 1 controller wdc1 at isa? port "IO_WD2" bio irq 15 disk wd2 at wdc1 drive 0 disk wd3 at wdc1 drive 1 options ATAPI #Enable ATAPI support for IDE bus options ATAPI_STATIC #Don't do it as an LKM device acd0 #IDE CD-ROM device wfd0 #IDE Floppy (e.g. LS-120) # A single entry for any of these controllers (ncr, ahb, ahc) is # sufficient for any number of installed devices. controller ncr0 controller ahb0 controller ahc0 controller isp0 # This controller offers a number of configuration options, too many to # document here - see the LINT file in this directory and look up the # dpt0 entry there for much fuller documentation on this. controller dpt0 controller adv0 at isa? port ? cam irq ? controller adw0 controller bt0 at isa? port ? cam irq ? controller aha0 at isa? port ? cam irq ? #controller aic0 at isa? port 0x340 bio irq 11 controller scbus0 device da0 device sa0 device pass0 device cd0 #Only need one of these, the code dynamically grows device wt0 at isa? port 0x300 bio irq 5 drq 1 device mcd0 at isa? port 0x300 bio irq 10 controller matcd0 at isa? port 0x230 bio device scd0 at isa? port 0x230 bio # atkbdc0 controlls both the keyboard and the PS/2 mouse controller atkbdc0 at isa? port IO_KBD tty device atkbd0 at isa? tty irq 1 device psm0 at isa? tty irq 12 device vga0 at isa? port ? conflicts # splash screen/screen saver pseudo-device splash # syscons is the default console driver, resembling an SCO console device sc0 at isa? tty # Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver #device vt0 at isa? tty #options XSERVER # support for X server #options FAT_CURSOR # start with block cursor # If you have a ThinkPAD, uncomment this along with the rest of the PCVT lines #options PCVT_SCANSET=2 # IBM keyboards are non-std device npx0 at isa? port IO_NPX irq 13 # # Laptop support (see LINT for more options) # device apm0 at isa? flags 0x31 # Advanced Power Management # PCCARD (PCMCIA) support controller card0 #device pcic0 at card? #device pcic1 at card? #MNS You may need to reset all pccards after resuming #options PCIC_RESUME_RESET # reset after resume device sio0 at isa? port "IO_COM1" flags 0x10 tty irq 4 device sio1 at isa? port "IO_COM2" tty irq 3 # MNS sio2 PCMCIA modem at irq 11 device sio2 at isa? port "IO_COM3" tty irq 11 device sio3 at isa? disable port "IO_COM4" tty irq 9 # Parallel port device ppc0 at isa? port? net irq 7 controller ppbus0 device nlpt0 at ppbus? device plip0 at ppbus? device ppi0 at ppbus? #controller vpo0 at ppbus? # Order is important here due to intrusive probes, do *not* alphabetize # this list of network interfaces until the probes have been fixed. # Right now it appears that the ie0 must be probed before ep0. See # revision 1.20 of this file. device ax0 device de0 device fxp0 device mx0 device pn0 device rl0 device tl0 device tx0 device vr0 device vx0 device wb0 device xl0 device ed0 at isa? port 0x280 net irq 10 iomem 0xd8000 device ie0 at isa? port 0x300 net irq 10 iomem 0xd0000 device ep0 at isa? port 0x300 net irq 10 device ex0 at isa? port? net irq? device fe0 at isa? port 0x300 net irq ? device le0 at isa? port 0x300 net irq 5 iomem 0xd0000 device lnc0 at isa? port 0x280 net irq 10 drq 0 #device ze0 at isa? port 0x300 net irq 10 iomem 0xd8000 #device zp0 at isa? port 0x300 net irq 10 iomem 0xd8000 device cs0 at isa? port 0x300 net irq ? pseudo-device loop pseudo-device ether pseudo-device sl 1 pseudo-device ppp 1 pseudo-device tun 4 pseudo-device pty 16 pseudo-device gzip # Exec gzipped a.out's # KTRACE enables the system-call tracing facility ktrace(2). # This adds 4 KB bloat to your kernel, and slightly increases # the costs of each syscall. options KTRACE #kernel tracing # This provides support for System V shared memory and message queues. # options SYSVSHM options SYSVMSG # The `bpfilter' pseudo-device enables the Berkeley Packet Filter. Be # aware of the legal and administrative consequences of enabling this # option. The number of devices determines the maximum number of # simultaneous BPF clients programs runnable. pseudo-device bpfilter 4 #Berkeley packet filter # USB support #controller uhci0 #controller ohci0 #controller usb0 # # for the moment we have to specify the priorities of the device # drivers explicitly by the ordering in the list below. This will # be changed in the future. # #device ums0 #device ukbd0 #device ulpt0 #device uhub0 #device ucom0 #device umodem0 #device hid0 #device ugen0 # #options USB_DEBUG #options USBVERBOSE #MNS pseudo-device vn #Vnode driver (turns a file into a device) # Audio drivers: `snd', `sb', `pas', `gus', `pca' # # snd: Voxware sound support code # sb: SoundBlaster PCM - SoundBlaster, SB Pro, SB16, ProAudioSpectrum # sbxvi: SoundBlaster 16 # sbmidi: SoundBlaster 16 MIDI interface # pas: ProAudioSpectrum PCM and MIDI # gus: Gravis Ultrasound - Ultrasound, Ultrasound 16, Ultrasound MAX # gusxvi: Gravis Ultrasound 16-bit PCM (do not use) # mss: Microsoft Sound System # css: Crystal Sound System (CSS 423x PnP) # sscape: Ensoniq Soundscape MIDI interface # sscape_mss: Ensoniq Soundscape PCM (requires sscape) # opl: Yamaha OPL-2 and OPL-3 FM - SB, SB Pro, SB 16, ProAudioSpectrum # uart: stand-alone 6850 UART for MIDI # mpu: Roland MPU-401 stand-alone card # # Beware! The addresses specified below are also hard-coded in # i386/isa/sound/sound_config.h. If you change the values here, you # must also change the values in the include file. # # pcm: PCM audio through various sound cards. # # This has support for a large number of new audio cards, based on # CS423x, OPTi931, Yamaha OPL-SAx, and also for SB16, GusPnP. # For more information about this driver and supported cards, # see the pcm.4 man page and /sys/i386/isa/snd/CARDS. # # The flags of the device tells the device a bit more info about the # device that normally is obtained through the PnP interface. # bit 2..0 secondary DMA channel; # bit 4 set if the board uses two dma channels; # bit 15..8 board type, overrides autodetection; leave it # zero if don't know what to put in (and you don't, # since this is unsupported at the moment...). # # This driver will use the new PnP code if it's available. # # pca: PCM audio through your PC speaker # # If you have a GUS-MAX card and want to use the CS4231 codec on the # card the drqs for the gus max must be 8 bit (1, 2, or 3). # # If you would like to use the full duplex option on the gus, then define # flags to be the ``read dma channel''. # # options BROKEN_BUS_CLOCK #PAS-16 isn't working and OPTI chipset # options SYMPHONY_PAS #PAS-16 isn't working and SYMPHONY chipset # options EXCLUDE_SBPRO #PAS-16 # options SBC_IRQ=5 #PAS-16. Must match irq on sb0 line. # PAS16: The order of the pas0/sb0/opl0 is important since the # sb emulation is enabled in the pas-16 attach. # # To overide the GUS defaults use: # options GUS_DMA2 # options GUS_DMA # options GUS_IRQ # # The i386/isa/sound/sound.doc has more information. # Controls all "VOXWARE" driver sound devices. See Luigi's driver # below for an alternate which may work better for some cards. # controller snd0 #device pas0 at isa? port 0x388 irq 10 drq 6 device sb0 at isa? port 0x220 irq 5 drq 1 #device sbxvi0 at isa? drq 5 #device sbmidi0 at isa? port 0x330 #device awe0 at isa? port 0x620 #device gus0 at isa? port 0x220 irq 12 drq 1 ##device gus0 at isa? port 0x220 irq 12 drq 1 flags 0x3 #device mss0 at isa? port 0x530 irq 10 drq 1 #device css0 at isa? port 0x534 irq 5 drq 1 flags 0x08 #device sscape0 at isa? port 0x330 irq 9 drq 0 #device trix0 at isa? port 0x330 irq 6 drq 0 #device sscape_mss0 at isa? port 0x534 irq 5 drq 1 #device opl0 at isa? port 0x388 #device mpu0 at isa? port 0x330 irq 6 drq 0 #device uart0 at isa? port 0x330 irq 5 # Luigi's snd code (use INSTEAD of snd0 and all VOXWARE drivers!). # You may also wish to enable the pnp controller with this, for pnp # sound cards. # #device pcm0 at isa? port ? tty irq 10 drq 1 flags 0x0 # Not controlled by `snd' #device pca0 at isa? port "IO_TIMER1" tty